pjtaxi Posted May 18 Report Share Posted May 18 Bought a 2020 Edge sel used. I was told it was a rental car with 5200 miles. Two different key fobs and no power liftgate. How do I find out the correct fob for this car? Thanks for any info Quote Link to comment Share on other sites More sharing options...
pjtaxi Posted May 28 Author Report Share Posted May 28 Alarm reset. Lost post about resetting hood ajar alarm. Someone mentioned to unplug alarm switch and touch both terminals together does this sound correct? thanks for any info. I will try to save the post this time. We have small dent in edge of hood. Hood latches fine. Quote Link to comment Share on other sites More sharing options...
Haz Posted May 28 Report Share Posted May 28 (edited) From the 2020 Edge Workshop Manual, with emphasis added... Placing your device cursor over underlined acronyms may yield full-words popup descriptions of their meaning. Arming The Perimeter Alarm The perimeter alarm is ready to arm any time the ignition is off. The perimeter alarm pre-arms when any of the following actions are carried out: Pressing the lock button on a RKE transmitter Pressing the door lock control switch to the lock position with a front door open, and then closing the door Touching the 7/8 and 9/0 buttons simultaneously on the keyless entry keypad Locking the vehicle with the passive entry feature Once the system is pre-armed, there is a 20-second countdown before the perimeter alarm is armed. Each entry point to the vehicle (hood, door and liftgate) is armed separately and must be closed before that entry point begins the 20-second countdown to become armed. If all entry points are closed, the turn signals flash upon locking to indicate all entry points are entering the 20-second countdown. Perimeter Alarm Activation The perimeter alarm has a 12-second delay when the driver front door is opened without using a valid programmed RKE transmitter, the keyless entry keypad or a passive key to unlock the vehicle. During the delay, a chime sounds. If the perimeter alarm is not disarmed within the 12-second delay, the alarm activates. The perimeter alarm activates when any of the following actions are carried out: The driver front door is opened without first receiving an unlock command from the passive entry feature, the keyless entry keypad or a valid programmed RKE transmitter, and the 12-second delay has expired. Any other door, the liftgate or the hood is opened without first receiving an electronic unlock command from the passive entry feature, the keyless entry keypad or a valid programmed RKE transmitter. the BCM detects an attempt by a diagnostic scan tool to establish communication on the CAN . The perimeter alarm only activates 10 times per arming cycle. After that, the alarm does not activate. To enable the perimeter alarm again, disarm the perimeter alarm and then arm it again. Disarming The Perimeter Alarm The perimeter alarm disarms when any of the following actions are carried out: Pressing the unlock button on a door lock control switch within the 20-second pre-arm The smart unlock feature activates within the initial 20-second pre-arm Pressing the unlock button on a valid programmed RKE transmitter Pressing the liftgate release button on a programmed RKE transmitter (this only disarms the liftgate entry point with the rest of the vehicle remaining armed) Using a valid programmed key to change the ignition to RUN Entering the correct vehicle unlock code on the keyless entry keypad Unlocking a front door or opening the liftgate using the passive entry feature The source of the above description is attached below as a PDF document... Good luck! Perimeter Anti-Theft Alarm - System Operation and Component Description - 2020 Edge Workshop Manual.pdf Edited May 28 by Haz 1 Quote Link to comment Share on other sites More sharing options...
Haz Posted May 28 Report Share Posted May 28 (edited) Providing information here, previously shared with @pjtaxi via Forum Messaging, regarding the initial key fob post... Thanks for providing me your Edge's VIN, which allowed me to call up a Ford report called the Historical Vehicle Bill of Material (HVBoM), which lists the original part numbers of all identified parts assembled into your specific Edge. The HVBoM states the original Ford part number for the keyless entry fobs supplied with your Edge was HC3T-15K601-AD. This is the three-button fob that you've describing as currently having. (This image is from an inactive eBay ad from which the fobs are sold out) Presently, the Ford part number to replace the originally supplied fobs is HC3Z-15K601-G. Good luck! Edited May 28 by Haz 1 Quote Link to comment Share on other sites More sharing options...
pjtaxi Posted May 28 Author Report Share Posted May 28 Alarm reset. Lost post about resetting hood ajar alarm. Someone mentioned to unplug alarm switch and touch both terminals together does this sound correct? thanks for any info. I will try to save the post this time. We have small dent in edge of hood. Hood latches fine. Well waiting for knew hood latch I jumped the connector with a paper clip and still shows hood ajar? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.